Carbolite EZS Series Manual do Utilizador

MF65-1.01 1 Installation, Operation & Maintenance Instructions 1200°C E-range Compact Tube furnaces Models: EHA, EVA, EHC, EVC EST,

E range 10 MF65-1.01 MF65-1.00 Fitting the extended work tube in an EVA/EVC/EVT/EVZ furnace (Tools required: 4mm Hex key.) The fit

E range MF65-1.01 11 11  Loosely fit the work tube support boss Figure 2-15 (5),

E range 12 MF65-1.01 MF65-1.00  If gas/vacuum end seals (14) Figure 2-17, page 12 are being fitted follow the separate fitting ins

E range MF65-1.01 13 13 2.5 Setting up – vertical models supplied without a stand

E range 14 MF65-1.01 MF65-1.00 Fitting the optional insulating plugs and radiation shield For optimum temperature uniformity ins

E range MF65-1.01 15 15 2.6 Electrical Connections The electrical supply MUST inco

E range 16 MF65-1.01 MF65-1.00 3 OPERATION The instructions for operating the temperature controller are given in a separate manual

E range MF65-1.01 17 17 To switch the furnace off, use both the Heater switch and t

E range 18 MF65-1.01 MF65-1.00 It is possible to use local trim in the end zone controllers to enter a positive or negative adjustme

E range MF65-1.01 19 19 4 MAINTENANCE 4.1 General Maintenance No routine maintena

E range 2 MF65-1.01 MF65-1.00 1 INTRODUCTION 1.1 Products Covered This manual contains installation and operating instructions for

E range 20 MF65-1.01 MF65-1.00 Before commencing any major repairs we recommend reference to the European Association representing t

E range MF65-1.01 21 21 5.7 Fuse Replacement Fuses are marked on the circuit diagr

E range 22 MF65-1.01 MF65-1.00 7 CIRCUIT DIAGRAMS 7.1 Single Phase 200 to 240V wiring diagram for: EHA12/150B to EHA12/600B &

E range MF65-1.01 23 23 8 FUSES & POWER SETTINGS 8.1 Fuses - For wiring diag

E range 24 MF65-1.01 MF65-1.00 8.3 Power Settings & Adjustment The furnace control system incorporates electronic power limitin

E range MF65-1.01 25 25 9.2 Environment The furnaces contain electrical parts and

E range 26 MF65-1.01 MF65-1.00 Notes:

E range MF65-1.01 27 27 Notes:

E range 28 MF65-1.01 Carbolite, Parsons Lane, Hope, Hope Valley, S33 6RB, England. Telephone: +44 (0)1433 620011 Fax: +44 (

E range MF65-1.01 3 3 Index to numbered items in Figure 1-1 and Figure 1-2 1- Ele

E range 4 MF65-1.01 MF65-1.00 2.3 Setting up – horizontal models The EHA and EHC horizontal models must have work tubes fitted befo

E range MF65-1.01 5 5 Fitting the standard work tube in an EST/EZS furnace. (No to

E range 6 MF65-1.01 MF65-1.00 Fitting the extended work tube in an EHA/EHC/EST/EZS furnace (Tools required: 4mm Hex key.) The fit

E range MF65-1.01 7 7 Index to numbered items in Figure 2-5, Figure 2-6, Figure 2-

E range 8 MF65-1.01 MF65-1.00 2.4 Setting up – vertical Models The EVA and EVC vertical models must have their stands assembled, th

E range MF65-1.01 9 9 Using the EVA/EVC/EVT/EVZ horizontally The EVA and EVC models